Hello! Thanks to everyone who helped me yesterday, but I could not solve the issue. I however identified the problem. I opened a new thread to better focus on the real problem.

I just set up a debian server, installed docker from the official repo and then immich using docker compose. When I run docker compose up -d (after a few seconds) my server loses internet connectivity: it can access local addresses (I can ssh into it) but cannot access the internet: ping linux.org fails.

if I put down immich (docker compose down) it starts working again. the issue is probably that docker is creating a network bridge that conflicts with the host.

After searching the web, I tried to create /etc/docker/daemon.json like this:

{
  "bip": "172.18.0.1/24",
  "default-address-pools": [
    {"base": "172.19.0.0/16", "size": 24}
  ]
}

after the changes systemctl restart docker, then wait 10 seconds for everything to restart correctly.
I tried different configurations of addresses here (every stackoverflow answer gave different values, so I tried all of them), but none of them worked. I don’t know how to get which values to put here (if this is actually the solution)

a strange behavior I observed is that running ip route flush 0/0 temporary solves the problem, until the restart of docker, and Immich works normally (at least the “normal” behavior, I don’t know if this affects some functionalities)

Any tips? This is my really first experience in self hosting and I have to admit it, I thought it would have been easier :P

In case you’ll need it, here’s the output of ip addr show:

0.0.0.0 dev veth4c84e92 scope link
0.0.0.0 dev veth1f88dcc scope link
0.0.0.0 dev vethda721de scope link
0.0.0.0 dev vethd123481 scope link
0.0.0.0 dev veth23a05f6 scope link
default dev veth4c84e92 scope link # this line and the line below disappear after the flush
default dev veth1f88dcc scope link # (this one)
default via 192.168.1.1 dev enp1s0
169.254.0.0/16 dev veth23a05f6 proto kernel scope link src 169.254.6.247
169.254.0.0/16 dev vethd123481 proto kernel scope link src 169.254.226.60
169.254.0.0/16 dev vethda721de proto kernel scope link src 169.254.248.163
169.254.0.0/16 dev veth1f88dcc proto kernel scope link src 169.254.136.146
169.254.0.0/16 dev veth4c84e92 proto kernel scope link src 169.254.29.133
169.254.0.0/16 dev enp1s0 scope link metric 1000
172.16.0.0/20 dev br-237d14e56e71 proto kernel scope link src 172.16.0.1
172.18.0.0/24 dev docker0 proto kernel scope link src 172.18.0.1 linkdown
192.168.1.0/24 dev enp1s0 proto kernel scope link src 192.168.1.4
192.168.1.1 dev enp1s0 scope link

EDIT: I gave up. I removed debian and installed fedora, and now it all works like a charm

  • tubbaduOP
    link
    fedilink
    1
    edit-2
    10 months ago

    I haven’t set up a firewall yet, I wanted first to make sure that everything works before installing one (I was thinking of ufw)

    I have a clean Debian install, I don’t know if there are some rules OOTB that can interfere…

    • @redxef@feddit.de
      link
      fedilink
      1
      edit-2
      10 months ago

      Better check, you definitely already have a firewall running since docker needs it for NAT. A fresh debian has, as far as I know nftables and iptables-nft installed.